-------------------- 1 --------------------
#1. RE: [E36M3] rsm gasket ? - from Robert Jackowitz
Top
Date: Thu, 2 Nov 2000 12:24:08 -0500 From: Robert Jackowitz <RJackowitz@HARVPART.COM> Subject: RE: [E36M3] rsm gasket ? I believe that would be 33 52 1 128 734. Yes, it should be done unless the gaskets on the RSM's are clean and in good shape. Generally, I think they are used to keep dirt and water from entering through the wheel well opening. Rob -----Original Message----- From: George M. Kofman [SMTP:sdg2@execpc.com] Sent: Thursday, November 02, 2000 12:16 PM To: E36M3 Subject: [E36M3] rsm gasket ? Date: Thu, 2 Nov 2000 11:17:50 -0600 From: "George M. Kofman" <sdg2@execpc.com> Subject: rsm gasket ? Hey folks; just got my JTD RSMs from another digester, and will try to install them this weekend. Reading through the docs they suggest replacing the "gasket" before installing new RSMs. Anyone know the PN for this ? should this be done ? TIA GMK '97 ///M3/4 (with E46M3 and E46 LTW on the waiting list :-) ************************************************************* List Commands UNSUBSCRIBE - (in subject line) unsubscribes you from the mailing list. *************************************************************
-------------------- 2 --------------------
#2. Re: [E36M3] rsm gasket ? - from nabli@attglobal.net
Top
Date: Thu, 02 Nov 2000 12:41:36 -0500 From: nabli@attglobal.net Subject: Re: [E36M3] rsm gasket ? 33 52 1 128 734 Cheers, Jim E. "George M. Kofman" wrote: > Date: Thu, 2 Nov 2000 11:17:50 -0600 > From: "George M. Kofman" <sdg2@execpc.com> > Subject: rsm gasket ? > > Hey folks; > > just got my JTD RSMs from another digester, and will try to install them > this weekend. Reading through the docs they suggest replacing the "gasket" > before installing new RSMs. Anyone know the PN for this ? should this be > done ? > > TIA > GMK > '97 ///M3/4 (with E46M3 and E46 LTW on the waiting list :-) > > ************************************************************* > List Commands > UNSUBSCRIBE - (in subject line) unsubscribes you from the mailing list. > *************************************************************
-------------------- 3 --------------------
#3. Re: RSM gasket - from RonStygar@aol.com
Top
Date: Thu, 2 Nov 2000 12:57:05 EST From: RonStygar@aol.com Subject: Re: RSM gasket Connect to: http://www.unofficialbmw.com/e36/suspension/e36_replace_rear_shock_bushi ngs.ht ml Ron@unofficialbmw.com FLY BMW Marlborough, CT www.unofficialbmw.com/ronstygar.html
-------------------- 4 --------------------
#4. Re: [E36M3] rsm gasket ? - from Jim Powell
Top
Date: Thu, 02 Nov 2000 09:58:39 -0800 From: Jim Powell <jsp98m3@home.com> Subject: Re: [E36M3] rsm gasket ? If you can get the old one off intact, the world won't end if you reuse it. Jim "George M. Kofman" wrote: > Date: Thu, 2 Nov 2000 11:17:50 -0600 > From: "George M. Kofman" <sdg2@execpc.com> > Subject: rsm gasket ? > > Hey folks; > > just got my JTD RSMs from another digester, and will try to install them > this weekend. Reading through the docs they suggest replacing the "gasket" > before installing new RSMs. Anyone know the PN for this ? should this be > done ? > > TIA > GMK > '97 ///M3/4 (with E46M3 and E46 LTW on the waiting list :-) > > ************************************************************* > List Commands > UNSUBSCRIBE - (in subject line) unsubscribes you from the mailing list. > *************************************************************
-------------------- 5 --------------------
#5. Front undertray replacement - from Steve Sharp
Top
Date: Thu, 02 Nov 2000 10:17:18 -0800 From: Steve Sharp <steve.sharp@xilinx.com> Subject: Front undertray replacement I had my front plastic undertray fall off while driving down the freeway the other day. Sounds like this is a common failure, especially if you drag the undertray over a parking barrier or two. Mine looks like the mounting "ears" where it bolts up to the car have fractured off. A replacement is only $85 at the local dealer. Is there anything tricky about getting it fastened back in place? Steve Sharp '97 M3/2
-------------------- 6 --------------------
#6. Re: [E36M3] Front undertray replacement - from Jim Powell
Top
Date: Thu, 02 Nov 2000 10:18:35 -0800 From: Jim Powell <jsp98m3@home.com> Subject: Re: [E36M3] Front undertray replacement Only if the mounting screws ripped out of the wheel well liners. I personally recommend that you look at replacing it permanently with A JTD underfairing. The BMW parts are virtual junk. Jim Steve Sharp wrote: > Date: Thu, 02 Nov 2000 10:17:18 -0800 > From: Steve Sharp <steve.sharp@xilinx.com> > Subject: Front undertray replacement > > I had my front plastic undertray fall off while driving down the freeway > the other day. Sounds like this is a common failure, especially if you > drag the undertray over a parking barrier or two. Mine looks like the > mounting "ears" where it bolts up to the car have fractured off. > > A replacement is only $85 at the local dealer. Is there anything tricky > about getting it fastened back in place? > > Steve Sharp > '97 M3/2 > > ************************************************************* > List Commands > UNSUBSCRIBE - (in subject line) unsubscribes you from the mailing list. > *************************************************************
-------------------- 7 --------------------
#7. Re: Front undertray replacement - from S Lafredo
Top
Date: Thu, 2 Nov 2000 10:34:19 -0800 (PST) From: S Lafredo <slafredo@yahoo.com> Subject: Re: Front undertray replacement You just need a ratchet or nut driver with a long extension. You will also need to remove the pork chops/triangles b/c the snap onto the center section. Also don't forget to put the air diffuser back into the new center panel. If I remember correctly the nuts are 13mm. HTH. Stephen slafredo@b-t-g.com http://b-t-g.com --- Steve Sharp <steve.sharp@xilinx.com> wrote: > Date: Thu, 02 Nov 2000 10:17:18 -0800 > From: Steve Sharp <steve.sharp@xilinx.com> > Subject: Front undertray replacement > > I had my front plastic undertray fall off while driving down the > freeway > the other day. Sounds like this is a common failure, especially if > you > drag the undertray over a parking barrier or two. Mine looks like the > mounting "ears" where it bolts up to the car have fractured off. > > A replacement is only $85 at the local dealer. Is there anything > tricky > about getting it fastened back in place? > > Steve Sharp > '97 M3/2 > > > > ************************************************************* > List Commands > UNSUBSCRIBE - (in subject line) unsubscribes you from the mailing > list. > ************************************************************* > > > > __________________________________________________ Do You Yahoo!? From homework help to love advice, Yahoo! Experts has your answer. http://experts.yahoo.com/
-------------------- 8 --------------------
#8. RE: [E36M3] Turner Motorsports and Jim Conforti in San Diego - from Mount, Mike
Top
Date: Thu, 2 Nov 2000 11:24:41 -0800 From: "Mount, Mike" <JMMn@pge.com> Subject: RE: [E36M3] Turner Motorsports and Jim Conforti in San Diego Okay Jim, that was a nice teaser, but.... "where's the beef!!?" Where's the good stuff, the info, Jim C.'s new products, pictures of the scantily clad dancers, etc etc???? Mike (5 hours north of SD) '95 M3 da kar is yellow Subject: Turner Motorsports and Jim Conforti in San Diego http://www.sdbmwcca.com/Turner/Turner.htm
-------------------- 9 --------------------
#9. Re: [E36M3] Turner Motorsports and Jim Conforti in San Diego - from Jim Powell
Top
Date: Thu, 02 Nov 2000 11:47:05 -0800 From: Jim Powell <jsp98m3@home.com> Subject: Re: [E36M3] Turner Motorsports and Jim Conforti in San Diego No new products. No dancing girls. But...... In my mind the real highlight of the show was meeting the people. While I didn't talk to Jim Conforti, I did talk for quite a while with Will Turner and Don Salama. Let me tell you, I was impressed with how nice and O R D I N A R Y guys they were. I also talked to a woman who I *assume* might have been Will's mother. She was very gracious and informative about Will's formative years :) Bottom line: I'm a total butthead of a human being and I was very impressed. A great deal of my rather large annual parts budget is likely to suddenly consolidate into Turner Motorsports. Sure I'll still bargain hard with them on a few items I haven't bought there in the past because I thought the price was a little high, but I'm a Turner convert. Take it for what it's worth from an outspoken, miserly cheapskate. Jim "Mount, Mike" wrote: > Date: Thu, 2 Nov 2000 11:24:41 -0800 > From: "Mount, Mike" <JMMn@pge.com> > Subject: RE: [E36M3] Turner Motorsports and Jim Conforti in San Diego > > Okay Jim, that was a nice teaser, but.... "where's the beef!!?" > Where's the good stuff, the info, Jim C.'s new products, pictures of the > scantily clad dancers, etc etc???? > Mike (5 hours north of SD) > '95 M3 > da kar is yellow > > Subject: Turner Motorsports and Jim Conforti in San Diego > > http://www.sdbmwcca.com/Turner/Turner.htm > > ************************************************************* > List Commands > UNSUBSCRIBE - (in subject line) unsubscribes you from the mailing list. > *************************************************************
-------------------- 10 --------------------
#10. Alternate source for Dinan CAI - from Bora Akyol
Top
Date: Thu, 02 Nov 2000 13:26:32 -0800 From: Bora Akyol <akyol@pluris.com> Subject: Alternate source for Dinan CAI Does anyone know of a Dinan dealer that sells the CAI for a discount to BMWCCA members? Thanks Bora